Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Bloomington
If your automatic gate in Bloomington stopped working or your openers are failing, our Electric Gate Repair team fixes it, and usually in one visit. Most electric gate repairs in Bloomington run between $140 and $600 depending on whether the problem is a bad capacitor, a sun-cracked limit switch, or a motor that’s finally given up. Call us at (877) 517-5469 and we’ll give you a straight answer over the phone before we ever send a truck out. We work on gates off Cactus Avenue, Slover Avenue, Cedar Avenue, and every unincorporated pocket of 92316, and we know these older systems from the first bolt to the last photocell.
Why San Diego Gate Company Is Bloomington’s Preferred Electric Gate Repair Company
Bloomington is a different kind of service area. It’s unincorporated county land with half-acre and larger lots, long driveways, RV gates, and wrought iron that’s been baking in the Inland Empire sun since the Reagan administration. The gate hanging on your cinderblock wall probably wasn’t installed by a gate specialist. It was installed by a welder who did fences, or a general contractor who did gates on the side. That’s why so many Bloomington homeowners call us after a second or third failed repair from someone who guessed at the problem.
Rob Vickers built San Diego Gate Company as a pure-play gate shop. We don’t do garage doors on the side, we don’t do fencing, and we don’t get distracted by other trades. Every tech on the truck is trained on Electric Gate Repair in Bloomington systems specifically, from old LiftMaster operators to newer FAAC and DoorKing units. Our customers in Bloomington consistently tell us the same thing: we diagnosed in minutes what another company couldn’t figure out in three visits. That’s not magic. It’s that we only work on gates.
We’re licensed and insured, and we quote every repair before any work starts. No surprises, no upsell to a replacement when a $60 capacitor swap fixes the problem.
Styles & brands we work with
Automatic Gate Repair in Bloomington
Automatic Gate Repair in Bloomington usually means diagnosing why a gate that worked fine for 25 years now stops halfway, grinds against the track, or refuses to open at all. Older automated systems in this area fail from heat fatigue and exposed wiring more than anything else. Summers push attic-threshold temperatures into control boxes mounted on south-facing block walls, and the resulting expansion and contraction loosens terminal connections on the control board. What starts as a phantom stop or a keypad that occasionally ignores the code spirals into a dead operator within a month or two.
So when a Bloomington homeowner calls and says the gate is “acting up,” we start with the control board and the limit settings before we touch the motor. A standard automatic gate repair in Bloomington pricing runs $140 to $400 for component-level fixes, and $400 to $600 when the operator or motor has failed. We give you the number before we touch a screwdriver.
Control Board Diagnosis and Replacement
The control board is the brain of the automatic gate. On older LiftMaster and Linear operators common across Bloomington’s 1980s and 1990s lots, these boards weren’t sealed well against dust and the dry, gritty air that blows through the Santa Ana corridor. Corrosion on the relay contacts and heat-brittle solder joints cause exactly the intermittent behavior that mimics a failing motor. The repair is usually a direct board replacement, and the new board works with your existing motor and limit switches.
Limit Switch and Loop Detector Repair
When the gate overshoots or stops a foot short of closed, the limit switches have drifted or failed. When it won’t open for your truck but opens for the neighbor’s Honda, the loop detector under the driveway has lost sensitivity or cracked. Both are part of routine automatic gate repair in Bloomington, and both are cheaper to fix than a motor replacement.
Electric Gate Motor in Bloomington
Electric Gate Motor replacement in Bloomington becomes necessary when the operator unit, the swing arm, or the rack-and-pinion drive has physically failed rather than just lost its programming. You’ll know the difference by the sound. A struggling motor that still moves the gate but whines and labors is often repairable. A motor that hums and doesn’t move, or trips its breaker immediately on command, is done. The most common driveway gate motors we replace in 92316 are older LiftMaster swing-arm units on double-swing RV gates and aging Viking or Mighty Mule slide operators on the long, straight side lots so common here.
A full Electric Gate Motor swap in Bloomington runs $500 to $900 including the motor, mounting hardware, wiring terminations, and a full re-tune of the open and close limits. If the motor failed because a Santa Ana bent the gate frame and put the whole drive line out of alignment, we fix the mechanical alignment first, then the motor. Putting a new motor on a bent gate just burns out the new motor.
Swing Gate Motor Replacement
Double-swing gates on RV access points are the most common job we do in Bloomington neighborhoods where every other house has boat or toy-hauler parking behind the fence. The swing arms live in direct sun, the hinge posts lean over time, and the operator ends up pushing against a gate that’s fighting back. Replacing the motor requires checking the post footing, not just unbolting a box and swapping it.
Slide Gate Motor and Track Repair
The slide gates on Bloomington’s long side yards and rear-access driveways take the worst of the Santa Ana season. Wind loads push the gate sideways against its track, the rollers score the steel, and the rack section bends. The motor then strains against a gate it can’t move cleanly. We repair and replace slide motors, but we also straighten rack sections and re-set track rollers, because a new motor on a bad rack is a $700 band-aid.
Trusted Brands We Service in Bloomington
We service DoorKing, Elite, Mighty Mule, and LiftMaster systems every week in Bloomington, along with FAAC, BFT, Linear, Viking, and Ghost Controls, so we can handle DoorKing repair in Bloomington without pushing a different brand. That means we stock or can quickly source the control boards, limit switches, photo-eyes, and remotes these older and newer systems expect. You won’t wait a week for a part to ship from a distributor in Texas. And because we work across all these brands, we won’t tell you to replace a perfectly good DoorKing just because our guy was trained on LiftMaster. We know how your system works because that’s all we do.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Bloomington Homes
- Sun-cracked welds on wrought-iron hinge points. Bloomington’s dry heat and intense UV exposure causes the paint to fail first, then the steel weld underneath. The gate sags at the hinge post, scrapes the driveway, and the operator labors. The fix is refitting and rewelding the hinge, not replacing the gate.
- Obsolete control boards that refuse modern safety photocells. Older LiftMaster and Linear boards from the 1980s and 1990s run on older low-voltage logic that doesn’t play well with the current-entrapment-protection sensors required by county code. We retrofit compatible boards and align the photocells rather than asking you to replace a working motor.
- Santa Ana wind damage to RV-access gates. A double-swing gate on a long driveway acts like a sail. After a strong wind event, the frames bend, the post anchors in cinderblock loosen or blow out, and the gate binds. We reset the hinge post footing and pull the frame square before the operator gets damaged.
- Slide gate rack and pinion misalignment on side-yard gates. The long slide gates common on Bloomington’s larger parcels get dirt and gravel in the track, then the rollers grind, and the rack drifts. The motor sounds like it’s working too hard because it is. Cleaning and re-aligning the rack usually restores normal operation.
Pricing for Electric Gate Repair in Bloomington, CA
Here’s what Bloomington homeowners actually pay us. Control board replacement runs $180 to $450 including the board and labor. Limit switch and photocell repair runs $140 to $300. A full swing gate motor replacement runs $500 to $900. Slide gate motor replacement with rack and track alignment runs $600 to $950. Keypad and remote control programming or replacement runs $90 to $250. Loop detector replacement under the driveway runs $220 to $400.
The spread depends on the brand, the age of your wiring, and whether the gate frame needs mechanical correction before the new part goes in. Every Bloomington quote is a fixed number, given before work starts, and we don’t add labor after the fact. Call (877) 517-5469 and we’ll give you a real number over the phone, and a free on-site estimate if the problem needs eyes on it.
We Also Serve Cities Near Bloomington
Our Electric Gate Repair team covers Bloomington and the surrounding Inland Empire communities from Bloomington out to Fontana, Rialto, Glen Avon, and Pedley. If you’re in one of those cities and your gate is acting up, the same real diagnosis and fixed pricing applies. Call us and we’ll get a tech out to you, usually within the same week, often within a day or two depending on the neighborhood and the schedule.
Serving Bloomington, CA — Our Local Coverage Area
We’re based in the Bloomington area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Bloomington
In most cases, yes, the operator can be retrofitted. Older control boards run on lower-voltage logic that doesn’t always recognize the entrapment-protection sensors that San Bernardino County code now requires. We replace the control board with a compatible unit and wire in modern photo-eyes and edge sensors. If the motor itself still runs clean, you keep it. Total cost for a retrofit runs $300 to $600, which is less than a full motor replacement. Call (877) 517-5469 and we’ll tell you over the phone whether your unit can take the upgrade.
Yes. When a hinge post pulls free from a cinderblock wall, we cut out the failed anchor area, set new threaded anchors or through-bolts into the block cores, and re-seat the hinge with a proper steel backing plate. This is a common repair on Bloomington’s older block-wall lots, and it does not require rebuilding the wall. The repair typically runs $250 to $500 per hinge post depending on how much of the block face has spalled away.
Not for a direct operator or motor replacement. San Bernardino County treats gate operator repair and replacement as routine maintenance when the work doesn’t change the gate’s footprint, height, or structural design. However, if you’re adding new entrapment protection, converting a manual gate to automatic, or altering the gate posts and footings, county code enforcement may want to see the work. We’ll tell you on the front end whether your specific repair triggers a permit, and we handle the county paperwork when it does. Call (877) 517-5469 with your street address if you want a straight answer before you touch anything.
The usual cause is a bent gate frame or a misaligned track putting the rack and pinion under load. After a Santa Ana event, slide gates on Bloomington’s side yards get pushed sideways enough to bind the rollers. The motor then works against the mechanical resistance and draws excess current, which shortens its life. The fix is straightening the rack and re-setting the track rollers, usually $300 to $500, rather than replacing the motor. Call (877) 517-5469 and we’ll diagnose it on site.
Yes. We convert older hardwired keypads and loop detectors to wireless or low-voltage solar-compatible systems all the time on Bloomington’s RV-access gates. The swap includes a compatible receiver, keypad reprogramming, loop detector adjustment, and full testing with the new solar operator. The conversion runs $250 to $550 including parts and labor, depending on your existing wiring and distance from the house. Call (877) 517-5469 for an exact quote on your particular gate.
On a half-acre lot off Bloomington’s Cactus Avenue, we repaired a double-swing driveway gate whose original 1980s LiftMaster operator kept tripping its safety photocell after a Santa Ana wind event bent the gate frame and cracked the hinge post weld. We reset the hinge post footing, replaced the obsolete control board with a compatible FAAC unit, and realigned the safety photo-eyes. The gate has run daily since without a single fault. That’s the kind of repair you can’t get from a company that splits its time between garage doors and fences. It takes a gate specialist, and the county’s unincorporated building code means you want someone who knows the difference between what Fontana requires and what San Bernardino County requires. We do.
If your gate on any lot in 92316 is misbehaving, call San Diego Gate Company at (877) 517-5469. We’ll give you a straight diagnosis, a fixed Bloomington price, and a repair that’s done right the first time.
Written by Rob Vickers, Owner at San Diego Gate Company, serving Bloomington and the Inland Empire.